Inspired by Yesterday's Legends. Built for Today.

Micro Voice Traceray is a cutting-edge polyphonic synth voice designed for powerful, immediate sound creation within Voltage Modular. With its huuuge stereo unison oscillator, powerful secondary oscillator, and a hefty sub oscillator the sound palette reaches from the widest supersaws to the phattest squares and beyond. A flexible multi-mode dual-filter with lots of character and grit tames the massive spectrum. Get things moving with the on-board modulation. Besides the dedicated amplifier envelope, there's a flexible modulation envelope that can do everything from ADSR, ASR, to AD envelope with lots of shaping and modulation capabilities. A stereo LFO gets things swirling and moving all over the place. This whole package is carefully finished by a sample-rate reducer, a neat matrix chorus, a stereo delay, and a versatile EQ section.

MANUAL

INTERFACE

  • PITCH CV
    • 1V/Octave pitch CV input
  • OCT Knob
    • Set the base octave
  • LEGATO Knob
    • set the time overlapping notes glide in pitch
  • MOD ENV Knob
    • Envelope Modulation strength on the pitch
  • VIB FREQ Knob
    • Controls the frequency of the pitch vibrato
  • VIB AMNT Knob
    • Controls the amount/strength of the pitch vibrato
  • VIB AMNT CV
    • Modulates the vibrato amount from 0 to the knob setting
  • GATE CV
    • Gate input that controls the AMP and MOD ENVelope
  • VCO/LFO SYNC switches
    • Retrigger the VCOs/LFO when a new gate is received
  • VELOCITY CV
    • Controls the output level
    • NOTE: the CV is sampled and held when a new gate is received
  • EXT IN CV
    • Feed an external signal into the internal MIXER

AMP and MOD ENV

  • ATTACK Knob
    • Set the attack time of the envelope
    • NOTE: the attack phase starts at the current envelope level. If the release phase is not finished the attack picks up where the release was.
  • Attack Shape Knob
    • Shapes the attack curve from inward to linear to outward
  • Decay Knob
    • Set the decay time of the envelope
  • Decay Shape Knob
    • Shapes the decay curve from inward to linear to outward
  • Sustain Knob
    • Set the sustain level of the envelope
  • Release Knob
    • Set the release time of the envelope
    • NOTE: the release phase starts as soon as the gate is low regardless of which stage the envelope is currently at
  • Release Shape Knob
    • Shapes the release curve from inward to linear to outward
  • Mode Switch
    • Changes the mode the envelopes operates in between:
      • ADSR - Attack Decay Sustain Release
        • Classic mode with 4 stages
      • ASR - Attack Sustain Release
        • No Decay, attack goes up to sustain level
      • AD - Attack Decay
        • When triggered will go through attack and decay regardless of gate
  • OUTPUT CV
    • Direct output of the envelope signal

LFO

  • WAVE Knob
    • Set the LFO waveform:
      • Sine
      • Triangle
      • Saw
      • Square
      • Stepped Random
      • Smooth Random
  • ONSET Knob
    • Set the onset time the LFO takes to reach full level
    • NOTE: the LFO onset is exponential
  • FREQ Knob
    • Set the LFO frequency
    • NOTE: when SYNC is enabled the time is set in relation to the set BPM
    • NOTE: When LFO FREQ Knob is fully turned up the LFO is set to C1 and can be played in pitch with 1V/Octave signals on the FREQ CV input
  • FREQ CV
    • Exponential CV input to modulate the LFO frequency
  • SYNC Switch
    • Set tempo sync for the LFO frequency
  • Smooth Knob
    • Smooths the LFO output with a gentle filter that follows the LFO's frequency
  • Stereo Knob
    • Adds a phase offset to the right channel
  • Phase Knob and CV
    • Sets the overall phase offset of both channels
    • NOTE: When LFO is re-triggered it will reset back to this position (right channel with additional stereo phase offset)
  • RETRIG CV
    • Retriggers the LFO to the set PHASE
  • Stereo OUTPUT
    • Direct output of the LFO signal

VCO1

  • SYNC Knob (with CV, ENV and LFO modulation)
    • Sets the frequency multiplier for the hard-sync
  • STEREO Knob (with ENV modulation)
    • Sets the stereo width of the output
    • NOTE: is more effective when more unison voices are active
  • MORPH Knob (with CV, ENV and LFO modulation)
    • Morphs the waveform between SAW and SQUARE
  • PWM Knob (with CV, ENV and LFO modulation)
    • Sets the Pulse-Width of the Square waveform
  • UNISON Switch
    • Sets the number of unison voices
  • DETUNE Knob
    • Sets the pitch detune of the unison voices
  • PHASE Knob (with ENV modulation)
    • Sets the phase offset of each successive unison voice
  • DRIFT Knob
    • Sets the random pitch drift of each unison voice
  • JITTER Knob
    • Sets the random pitch jitter of each unison voice
  • DETPH Knob (with ENV modulation)
    • Controls the unison depth by attenuating further spread unison voices
  • Stereo OUTPUT
    • Direct output of the VCO1 signal

VCO2

  • ENABLE Toggle Button
    • Enable or disable VCO2
  • DETUNE Knob
    • Pitch detune of VCO2 relative to the received PITCH CV signal
  • MORPH Knob (with CV and LFO modulation)
    • Morphs the waveform between SAW and SQUARE
  • PWM Knob (with CV and LFO modulation)
    • Sets the Pulse-Width of the Square waveform
  • SMOOTH Knob
    • Smooths the output with a gentle filter that follows the VCO's frequency
  • Stereo OUTPUT
    • Direct output of the VCO2 signal

SUB

  • ENABLE Toggle Button
    • Enable the SUB VCO
  • OCTAVE Switch
    • Set sub octave relative to the base PITCH (PITCH CV + Octave Knob)
  • SHAPE Knob
    • Set shape of the SUB VCO from sine to smooth square
  • OUTPUT
    • Direct output of SUB VCO signal

MIXER

  • VCO1/VCO2/SUB/EXT IN/NOISE Knobs
    • Set the level of the respective signal
  • Stereo OUTPUT
    • Direct output of MIXER signal

VCF1

  • FREQ Knob (with CV, ENV and LFO modulation)
    • Set the frequency of the filter
    • NOTE: if resonance is turned up to self-oscillation the filter can be played in pitch with this CV input
  • VELOCITY Knob
    • Sets how much velocity affects the filter cutoff frequency
  • TRACKING Knob
    • Set the filter frequency tracking for the input PITCH CV
  • RES Knob (with CV and LFO modulation)
    • Set the filter resonance
    • NOTE: at high values the filter starts to self-oscillate producing a sine wave
  • TYPE Switch
    • Set the filter type from LP/BP/HP
  • ROUTE Switch
    • Set the filter routing:
      • Only VCF1 (results in a 12dB/oct filter)
      • VCF1 in series with VCF2
      • VCF1 in parallel with VCF2
  • Stereo OUTPUT
    • Direct output of the VCF1 signal

VCF2

  • FREQ Knob (with CV, ENV and LFO modulation)
    • Set the frequency of the filter
    • NOTE: if resonance is turned up to self-oscillation the filter can be played in pitch with this CV input
  • VELOCITY Knob
    • Sets how much velocity affects the filter cutoff frequency
  • TRACKING Knob
    • Set the filter frequency tracking for the input PITCH CV
  • RES Knob (with CV and LFO modulation)
    • Set the filter resonance
    • NOTE: at high values the filter starts to self-oscillate producing a sine wave
  • TYPE Switch
    • Set the filter type from LP/BP/HP
  • LINK Switch
    • Set the link to VCF1:
      • Independent from VCF1
      • Cutoff and Resonance Knob settings copied from VCF1
      • Knob Settings and modulation copied from VCF1 (can still apply additional modulation with VCF2 modulation controls)
  • Stereo OUTPUT
    • Direct output of the VCF1 signal

CRUSHER

  • ENABLE Toggle Button
    • Enables the CRUSHER samplerate reduction effect
  • SRATE Knob (with CV, ENV and LFO modulation)
    • Set the Crusher samplerate
  • TRACK Knob
    • Set the crusher samplerate tracking for the input PITCH CV
  • SMOOTH Switch
    • Switches the crusher mode between:
      • none/discrete
      • linear
      • bezier

CHORUS

  • ENABLE Toggle Button
    • Enables the CHORUS effect
  • Depth Knob
    • Set the modulation depth
  • FREQ Knob
    • Set the modulation frequency
  • FDBK Knob
    • Set chorus feedback
    • NOTE: a special mixing matrix is applied to the 4 chorus voices that gives a crude reverberation effect at higher feedback settings
  • WET Knob
    • Dry/Wet signal ratio

DELAY

  • ENABLE Toggle Button
    • Enables the DELAY effect
  • MODE Switch
    • Set the stereo delay time mode:
      • Right channel can be set independently
      • Right channel can be set as an offset to the left channel
  • R/L Time Knob (with CV and LFO modulation)
    • Set the delay time
  • R/L Sync Switch
    • Set tempo sync for the delay times:
      • FREE/milliseconds
      • Tempo Synced divisions
      • 16ths note divisions
  • LPF/HPF Knob
    • Set the cutoff frequency of the feedback LowPass/HighPass Filter
  • WET Knob
    • Dry/Wet signal ratio

EQ

  • HI FREQ Knob
    • Set the frequency of the high EQ band
  • HI GAIN Knob
    • Set the gain of the high EQ band
  • HI TYPE Switch
    • Set the EQ band type between High-Shelf and Peak
  • MID FREQ Knob
    • Set the frequency of the middle EQ band
  • MID GAIN Knob
    • Set the gain of the middle EQ band
  • MID TYPE Switch
    • Set the EQ band type between wider or narrow peak
  • LOW FREQ Knob
    • Set the frequency of the low EQ band
  • LOW GAIN Knob
    • Set the gain of the low EQ band
  • LOW TYPE Switch
    • Set the EQ band type between Low-Shelf and Peak

OUTPUTS

  • LEVEL Knob
    • Set the overall output level of the signal
  • STEREO signal output